<track id="rb7zx"></track>
<form id="rb7zx"></form>
<menuitem id="rb7zx"></menuitem>

<ins id="rb7zx"><progress id="rb7zx"></progress></ins>

      <ruby id="rb7zx"><thead id="rb7zx"><video id="rb7zx"></video></thead></ruby><track id="rb7zx"></track>

          <pre id="rb7zx"><sub id="rb7zx"></sub></pre>

          <pre id="rb7zx"></pre><track id="rb7zx"><strike id="rb7zx"></strike></track>
          <p id="rb7zx"><form id="rb7zx"></form></p>


          問題

          原因

          解決

          泵浦運轉卡機或運轉不正常。

          逆止球閥、球座或磨損。

          更換

          泵浦不能運轉,或轉動一次就停止。

          空氣閥卡住或變髒。

          拆卸並清理空氣閥,使用過濾的空氣。

          逆止球閥嚴重磨損且卡進球
            座。

          更換球和球座

          因為過度受壓,逆止球閥卡進球座

          安裝釋壓閥

          泵浦運轉不規律

          吸入管線組塞

          檢查或清理

          球黏濕或洩漏。

          清理或更換

          膜片破裂

          更換

          排氣堵塞

          將堵塞移除

          液體裡含有空氣泡泡

          吸入管線鬆脫

          鎖緊

          膜片破裂

          更換

          入口歧管鬆脫,歧管和球座之間的密封墊受損

          旋緊歧管螺絲、更換球座密封墊

          排出氣體含液體

          膜片破裂

          更換

          接液膜片盤鬆脫

          鎖緊或更換


          PROBLEM

           CAUSE

          SOLUTION

          Pump cycles at   stall or fails to hold pressure
            at stall.

          Worn check valve   balls ,seats.

          Replace

          Pump will not   cycle, or cycles once and
            stops.

          Air valve is stuck   or dirty.

          Disassemble and   clean air valve.  Use filtered air.

          Check valve ball   is wedged into
            seat, due to overpressurization.

          Install Pressure   Relief Valve

          Pump operates   erratically.

          Clogged suction   line.

          Inspect; clear.

          Sticky or   leaking balls

          Clean or   replace.

          Diaphragm   ruptured.

          Replace.

          Restricted   exhaust.

          Remove   restriction.

          Air bubbles in   fluid.

          Suction line is   loose.

          Tighten.

          Diaphragm   ruptured.

          Replace

          Loose inlet   manifold, damaged
            seal between manifold and seat ,
            damaged o-rings.

          Tighten manifold   bolts or replace
            seats or o-rings.

          Loose diaphragm   shaft bolt.

          Replace ,Tighten   or replace

          Damaged o-ring

          Replace

          Fluid in exhaust   air.

          Diaphragm   ruptured.

          Replace

          Loose diaphragm   shaft bolt.

          Tighten or   replace


          2018年11月02日

          輸送有毒液體的正確安裝方式
          大流量找臺恩隔膜泵

          上一篇

          下一篇

          隔膜泵通氣不動作排查法

          <track id="rb7zx"></track>
          <form id="rb7zx"></form>
          <menuitem id="rb7zx"></menuitem>

          <ins id="rb7zx"><progress id="rb7zx"></progress></ins>

              <ruby id="rb7zx"><thead id="rb7zx"><video id="rb7zx"></video></thead></ruby><track id="rb7zx"></track>

                  <pre id="rb7zx"><sub id="rb7zx"></sub></pre>

                  <pre id="rb7zx"></pre><track id="rb7zx"><strike id="rb7zx"></strike></track>
                  <p id="rb7zx"><form id="rb7zx"></form></p>

                  无码av岛国片在线播放_乌克兰18videos极品_被粗大灌满了白浆_少妇无码av无码去区钱